Nlekọta anya maka nrụnye na igwe nnwale nke ụdị nko ụdị ogbugba ogbugba ï¼ˆä¸ ï¼ ï¼ ‰

- 2021-06-03-

Ndịụdị nko gbara ọgbụgba ọkụ igwen'ozuzu ha nwere ọdịdị ka ukwuu, yana usoro nrụnye dị mgbagwoju anya karịa nke obere akụrụngwa. Ezi nrụnye na igwe nnwale bụ isi ihe na -ahụ maka ịrụ ọrụ nke ngwa ndị ọzọ. N'ihe banyere arụmọrụ mbụ na -enweghị nkà, a chọrọ ndị ọrụ ịgbaso ntuziaka nke ndị ọrụ dị mkpa ma ọ bụ rụtụ aka na ntuziaka ahụ. Ịrụ ọrụ na -enweghị ikike nwere ike ibute mmebi ngwa ngwa na -enweghị atụnko gbara ọgbụgba ọkụ igwe. Ndịshot blasting machine manufacturer has sorted out the precautions for installation and test machine to share with you. I hope it will be helpful to users who use the device for the first time.
1. Installation. Ndịụdị nko gbara ọgbụgba ọkụ igwe is installed and debugged in the production plant and disassembled into several parts before being transported to the user site for installation. Although there is no pit, the foundation must be firm, the anchor bolt holes must be standardized, and the chamber body must be adjusted. After the second irrigation, the anchor bolt nuts can be tightened after solidification. After the chamber body is fixed, the various parts can be installed. Ndịprecautions for the installation and debugging of the relevant components are introduced below.
1. Ngwa ọgbụgba ọkụ:
Ndịshot blasting device has been installed on the chamber body before leaving the factory. Please pay attention to the problems to be debugged before use. Check whether the fixed positions of the blade, the pill wheel, the directional sleeve, and the guard plate are accurate and firm, and check whether the direction of rotation is correct after power on. Then adjust the position of the directional sleeve opening. Theoretically, the angle between the front edge of the directional opening and the front edge of the blade throwing position is about 900. After fixing the position of the directional sleeve, the position of the projectile belt can be detected by hanging Place a steel plate or wooden board on the position of the workpiece facing the exit of the shot blasting machine, start the shot blasting machine, put a small amount (2-5kg) of projectiles into the blasting tube, and then stop, check whether the hit position on the steel plate is suitable for the needs, such as Close the window of the bias-adjustable directional sleeve downwards, and vice versa, until it fits, and note the position of the directional sleeve opening as a basis for future replacement of the directional sleeve.
2. Ịwụnye na ịghasa ebu:
Buru ụzọ mee nnwale na-enweghị ibu iji lelee ma bọketị na-agagharị agagharị ma na-agbagharị agbagọ na-aga n'ụzọ ziri ezi, wee mezie eriri eriri ahụ ka ọ nwee oke esemokwu iji zere ịkpapụ, wee mee nnwale ibu iji lelee arụ ọrụ na ikike ebugharị, ma enwere mkpọtụ na ịma jijiji ọ bụla, lelee ma wepu ihe mgbochi.
3. Nkewa pill-sand:
Buru ụzọ chọpụta ma mmegharị ebule a na -agbanwe agbanwe, wee lelee ọnọdụ kwesịrị ekwesị nke efere ekewapụ, mgbe ahụ mgbe a na -eburu ihe ma na -agbagọ agbagọ, a na -enwe ntụtụ na -aga n'ihu n'ihu, wee chọpụta ma nchara nchara na -apụta na -ada. mgbe a na -ewepu akpa ahụ